Fraunhofer Institute for Electron BeamACTPHAST 4.0
ACceleraTing PHotonics innovAtion for SME’s: a one STop-shop-incubator
More information: www.actphast.eu
Funded by:
Europäische Union
Funding reference: 779472
Duration: 01.11.2017 - 31.10.2021
Finished Projects
ACTPHAST 4.0
Admont
Admont
Advanced Distributed Pilot Line for More-than-Moore Technologies
Funded by:
Europäische Union; Horizon 2020 Programm; ECSEL Joint Undertaking
Funding reference: 661796
Duration: 15.05.2015 - 30.04.2019
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 16ESE0058S
Duration: 15.05.2015 - 30.04.2019
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 16ESE0058S
Duration: 15.05.2015 - 30.04.2019
AlTiNTec
AlTiNTec
Investigation of technologies for the deposition of wear-reducing aluminium-rich TiAlN coatings
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100297970/3103
Duration: 01.07.2017 - 30.06.2019
Aluminium-rich titanium aluminium nitride coatings, which predominantly contain hard cubic phases, offer significantly better wear resistance compared to titanium aluminium nitride coatings with lower aluminium contents. With conventional PVD processes, such as magnetron sputtering or the arc process, predominantly cubic and stoichiometric titanium aluminum nitride coatings with an aluminum concentration > 32 at.% cannot be produced so far. In contrast, such aluminium-rich cubic titanium aluminium nitride layers can be deposited on hard metal substrates using a thermal CVD process. However, the reasons for the stabilization of the cubic phase in the CVD process at very high aluminum contents have not been clarified. Therefore, the relevant stabilization mechanisms shall be investigated, concepts for the improvement of the deposition of layers for the CVD process as well as for the considered PVD processes shall be developed, experimentally tested and the resulting layer and application properties shall be determined. The overall aim of this project is to investigate the mechanisms of CVD deposition in greater detail, to significantly improve the application properties of the titanium aluminium nitride coatings deposited by the PVD processes and to test PVD processes with a higher deposition rate and better coating properties.
ARIES
ARIES
Accelerator Research and Innovation for European Science and Society
More information
Funded by:
Europäische Union; Horizon 2020 Programm
Funding reference: 730871
Duration: 01.05.2017 - 30.04.2021BACKPLANE
BACKPLANE
Deep-submicron CMOS process technology for driving integrated microdisplays and evaluation circuits of optical sensors
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Sächsische AufbauBank
Funding reference: 100392259
Duration: 31.12.2019 - 31.10.2022BacterFilm
BacterFilm
Geobacter films as biologically produced organic plate electrodes
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 835 226
Duration: 21.06.2017 - 20.06.2018Bio2Ret
Bio2Ret
IBÖ-05: Development of a completely bio-based, steam sterilizable laminate for packaging applications with time-adapted
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 031B0696
Duration: 01.10.2018 - 30.09.2019bioElektron (MAVO)
MAVO bioElektron
Biodegradable electronics for aktive implants
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Duration: 01.01.2016 - 31.12.2018BiSWind
BiSWind
Joint project: Component-integrated sensors for power transmission elements in wind turbines
Funded by:
Bundesministerium für Wirtschaft und Energie
Funding reference: 0325891C
Duration: 01.12.2015 - 30.11.2018CARLEEN
CARLEEN
Investigation of highly efficient CSS-based CdTe-solar cells
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100206775/ 3005
Duration: 16.02.2015 - 15.02.2018CeGlaFlex (MAVO)
CeGlaFlex (MAVO)
Process chain for form-flexible ceramic and glass-based switching- and display elements
Until now, only insufficient approaches and processes existed to produce thin ceramics with high transparency, high shape accuracy as well as surface and edge quality in a continuous process chain. In addition to transparent, form-flexible ceramics, there is a particular lack of suitable processing technologies. The Fraunhofer joint project "CeGlaFlex" therefore aimed to investigate the development of processes and process chains for the processing of form-flexible ceramic and glass-based switching and display elements.
The project objectives were the production of thin and thus form-flexible transparent ceramics and display laminates with a thickness in the range of 100 μm, the processing of transparent form-flexible ceramics and thin glass composites without damaging the material functions, and the production of integrated switching and display elements on form-flexible substrates made of ceramic-glass composites.Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 833 916
Duration: 01.03.2017 - 28.02.2020CompExClean
CompExClean
kmU - SME-oriented self-research; Topics: "Development of a ring CT system for rapid inline testing of "endless" products and bulk materials" and "Compact electron beam technology for the degradation of pollutants in diesel exhaust gases".
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 838870/838845
Duration: 2019 - 2020CRT
CRT
Proof-of-Concept for quantitative measurement of capillary refill time
Funded by:
Medizinische Fakultät Carl Gustav Carus
Else Kröner-Fresenius-Zentrum für Digitale Gesundheit (EKFZ)
Funding reference: 061-303030
Duration: 01.12.2019 - 31.12.2021DANAE
DANAE
Investigation of thin-film and alignment technologies for nanoscale acoustic electronics. Sub-project: Coating technologies for piezoelectrically and acoustically effective layers in acoustic electronics.
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100206218
Duration: 01.02.2015 - 31.01.2018EFFKAB
EFFKAB
Efficient cabin architectures (EFFKAB), sub-theme: OLED lighting
Funded by:
Bundesministerium für Wirtschaft und Energie
Funding reference: 20K1503G
Duration: 01.01.2017 - 31.03.2019ElKaWe
ElKaWe
In the lighthouse project »ElKaWe«, six Fraunhofer Institutes under the direction of Fraunhofer IPM are working on the development of electrocaloric heat pumps for heating and cooling.
Fördergeber:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Förderkennzeichen: 840 005
Laufzeit: 01.10.2019 -30.09.2023ELITE NK cells
ELITE NK cells
Electron beam-based inactivation for the production of anti-tumor efficient NK cells
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Duration: 01.03.2018 - 28.02.2021ELOBEV
ELOBEV
Investigation of electrolytic coating systems for fasteners made of high-strength materials. Sub-project: Anti-corrosion coating in a rotary drum plant using a combination process
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 13XP5025D
Duration: 01.01.2017 - 31.12.2019ELVIRA
ELVIRA
Entwicklung einer Methode zur Elektronenstrahl-basierten Inaktivierung von Viren und Bakterien für die Impfstoffherstellung
Funded by:
Bill & Melinda Gates Foundation
Funding reference: OPP1154635
Duration: 01.09.2016 - 31.10.2018
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 826545
Duration: 01.03.2014 - 31.12.2017- 03 | 2021 – Inactivating pathogens using low-energy electrons
- 21 | 2018 – ELLI 300 – An innovative design for electron-beam treatment of liquids
- 26 | 2017 – Award for innovative advances in the utilization of low-energy electrons for medical applications
- 06 | 2017 – Inactivate vaccines faster and more effectively using electron beams
- 19 | 2016 – New procedure for producing safe and more effective vaccines
FAIR
FAIR
Support of physical functions through handsfree applications in extended reality (FAIR) Sub-project: ''Hardware-supported Eyetracking''
Funded by:
Verein Deutscher Ingenieure
Funding reference: 16SV5842
Duration: 01.11.2012 - 30.04.2016Flex+
Flex+
Open Innovation Platform
Funded by:
Bundesministerium für Bildung und Forschung, "Zwanzig20 - Partnerschaft für Innovation"
Funding reference: 03ZZF31
Duration: 01.01.2015 - 31.12.2016FLEX-G
FLEX-G
Joint project: Investigation of roll-to-roll technologies for the production of flexible and curved facade and roof elements with switchable total energy transmittance. Sub-project: Investigation of optoelectronic active layer systems on weather-stable fluoropolymer substrates
Funded by:
Bundesministerium für Wirtschaft und Energie
Funding reference: 03ET1470A
Duration: 01.06.2017 - 31.05.2020Forschungscluster
Forschungscluster
Mucosal application of RSV antigens to prevent juvenile bronchial asthma
Funded by:
Fraunhofer Cluster of Excellence Immune-Mediated Diseases CIMD
FoulingResist
FoulingResist
Efficiency improvement by reducing fouling in heat exchanger pipes. Sub project: Inner pipe coating with fouling-resistant thin layers.
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 3000658061
Duration: 01.09.2016 - 31.08.2018GEPARD
GEPARD
Basic research of InP Quantum Dots and their processing for application in high-resolution R, G, B displays, sub-theme: Structuring and excitation of Quantum Dots
Funded by:
Sächsisches Staatsministerium für Wissenschaft und Kunst
Funding reference: 100326378
Duration: 01.06.2018 - 31.05.2020GLADIATOR
GLADIATOR
Graphene Layers: Production, Characterization and Integration
Funded by:
Europäische Union (7th Framework Programme FP7)
Funding reference: GA#604000
Duration: 01.11.2013 - 30.04.2017Glass@Service
Glass@Service
Smart Service World, Joint project ''Glass@Service''
Funded by:
Bundesministerium für Wirtschaft und Energie
Funding reference: 01MD16008C
Duration: 01.01.2016 - 31.12.2018Hi-LED
Hi-LED
Human-centric intelligent LED engines for the take up of SSL in Europe
Funded by:
European Union (7th Framework Programme)
Funding reference: 619912
Duration: 01.12.2013 - 31.03.2017HiPERFORM
HiPERFORM
Reliable power electronics made of innovative materials for energy-efficient electromobility - sub-projects: Sputtering technology for epitaxial aluminium nitride/ gallium nitride layers
Funded by:
Europäische Union; Horizon 2020 Programm
Funding reference: 783174
Duration: 01.05.2018 – 30.04.2021
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 16EMOE023S
Duration: 01.05.2018 – 30.04.2021
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 16EMOE023S
Duration: 01.05.2018 – 30.04.2021
Hybrid-CVD
Hybrid-CVD
Collaborative project: Highly cross-linked and functional hybrid layers by plasma and thermally assisted deposition - subproject: Basic investigations on the combination of plasma and sol-gel technology
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 13XP5052E
Duration: 01.07.2018 - 30.06.2021InnoFlash
InnoFlash
Innovative pulse modulation for the operation of high power flash lamps
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100349243
Duration: 01.09.2018 - 31.08.2020KEF
KEF
Multisensor through visualizing conversion component for physical effects and fields
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 601055
Duration: 23.10.2017 - 22.10.2018KODOS
KODOS
Joint projects: Assembled thin glass laminate for optoelectronic systems Sub-theme: Coating of thin glass and production of OLED components
The KODOS project (Konfektionierter Dünnglas-Verbund für optoelektronische Systeme), funded by the German Federal Ministry of Education and Research (BMBF), aims to turn the innovative material thin glass into finished products along the entire value chain. To this end, the companies oriented towards application development EMDE development of light, Volkswagen and Deutsche Werkstätten Hellerau have joined forces with the technology suppliers tesa, VON ARDENNE, Flabeg, 4JET microtech, SURAGUS and the Fraunhofer Institute for Organic Electronics, Electron Beam and Plasma Technology FEP. The aim of the consortium is to be able to offer a complete kit of functional materials, semi-finished products, tools and technologies for the roll-to-roll production of optoelectronic systems on thin glass.
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 13N14607
Duration: 01.03.2019 - 28.02.2022KONFEKT
KONFEKT
Joint projects: Research on a convertible thin-glass substrate system for organic electronics applications (KONFEKT) - subproject: Technological studies on the roll-to-roll refinement of flexible glass ribbons
As part of the KONFEKT project, Fraunhofer FEP installed the FOSA labX 330 glass roll-to-roll coating system. The plant is primarily used to coat flexible glasses. The focus was on the coating materials indium tin oxide (ITO), niobium oxide and silicon oxide. The materials were used for anti-reflective coating systems and transparent electrodes. The FOSA labX 330 glass has the option of heating the substrate during coating. The project presents a calculation model on the basis of which the temperature of the glass can be estimated as a function of different heater settings. Both the situation without and the situation with coating were considered. It turned out that the glass can be heated up to temperatures above 400°C. This is particularly advantageous for the deposition of ITO. As a peak value, transparent ITO-based electrodes with a sheet resistance of 10 Ohm could be deposited. This corresponded to a specific conductivity of 1.7 x 10-4 Ohmcm. In addition to the electrical and optical properties, the surface topography was also considered. This was done in particular with a view to later application for organic light-emitting diodes. These require an electrode surface of very low roughness. It turned out that this property could only be achieved by a compromise with the opto-electrical properties.
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 13N13818
Duration: 01.03.2016 - 31.07.2018KriSiDET
KriSiDET
Innovative manufacturing processes of crystalline silicon layers for applications in energy technology
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100276968
Duration: 15.05.2017 - 14.05.2019LAOLA
LAOLA
Large-area OLED lighting applications on thin flexible substrates
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 03INT509AF
Duration: 01.08.2018 - 31.07.2021LiScell (MAVO)
LiScell (MAVO)
To lift-off with lithium sulphur: Cycle-stable and intrinsically safe battery cells with energy densities >400 Wh/kg
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Duration: 01.06.2014 - 31.05.2017LOIGB
LOIGB
LED- and OLED-integration in glass and plastic composites for use in lighting systems
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Duration: 17.09.2012 - 15.11.2014Funding reference: 100133280
LOMID
LOMID
Large cost-effective OLED microdisplays and their applications
The LOMID project will define pathways to the manufacture of flexible OLED microdisplays with an exceptionally large area (16 mm x 20 mm, screen diagonal of 25.4 mm) at acceptably high yields (>65%). This will be achieved by developing a robust silicon-based chip design allowing high pixel counts (1024×1280 (SXGA)) and high spatial resolution (pixel sizes of 10 μm x 10 μm corresponding to 2000 ppi). These display innovations will be coupled to a highly reliable manufacturing of the backplane.
Funded by:
Europäische Union; Horizon 2020 Programm
Funding reference: 644101
Duration: 01.01.2015 - 30.06.2018- 17 | 2018 – Enjoying virtual-reality-entertainment without headache or motion sickness
- 02 | 2018 – Develop data glasses faster
- 23 | 2017 – Lightweight, compact VR glasses made possible by large-area microdisplays
- 01 | 2017 – Large, but nevertheless micro – high resolution OLED microdisplay for virtual reality applications
MICRO3D
MICRO3D
Basic research on the precise joining of three-dimensional bodies with micromachining electron beamer.
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 3000653557
Duration: 16.06.2016 - 16.06.2019MiLEDI
MiLEDI
Micro Quantum Dot-Light Emitting Diode and Organic Light Emitting Diode Direct Patterning
Funded by:
Europäische Union; Horizon 2020 Programm
Funding reference: 779373
Duration: 01.01.2018 - 30.06.2021MobDi
MobDi
Promotion of the anti-corona project "MobDi - mobile disinfection
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 840 264
Duration: 01.10.2020 - 30.09.2021More information
MoLoKo
MoLoKo
Multiplex photonic sensor for plasmonic-based online detection of contaminants in milk
Fördergeber:
Europäische Union; Horizon 2020 Programm
Förderkennzeichen: 780839
Laufzeit: 01.01.2018 - 30.06.2021The main objective of MOLOKO project is the manufacturing, implementation and validation of a self-managing and automatic miniaturized integrated photonic sensor to be used as process analytical instrumentation for fastresponse on-site monitoring of interest analytes for security and quality within milk supply chain. In particular, we aim at realizing multiplexing quantitative detection of up to 10 analytes among which food safety parameters, e.g. antibiotics (i.e. penicillin, ampicillin, cephalonium) and toxins (i.e. mycotoxins and bacterial toxins) and food quality parameters e.g. lactoferrin and caseins by implementing a highly-integrated optoplasmonic-microfluidic sensor in the strategic checkpoints along the entire supply and value chain of milk.
MUSECORR
MUSECORR
Protection of cultural heritage by real-time corrosion monitoring
Funded by:
Europäische Union (7th Framework Programme FP7)
Funding reference: 226539
Duration: 01.06.2009 - 31.05.2012Neo-Sol
Neo-Sol
New technological steps for high-efficiency solar cells. Sub-project: Basic investigation on coating and electron beam processes for high-efficency solar cells.
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100272565/3355
Duration: 01.01.2017 - 31.12.2019Neptun
Neptun
Fundamental investigation of new processes and materials to increase the efficiency of CdTe solar cells (Neptun)
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100332352
Duration: 18.07.2017 - 31.07.2021OLEDSOLAR
OLEDSOLAR
Innovative manufacturing processes and in-line monitoring techniques for the OLED and thin film and organic photovoltaic industries (CIGS and OPV)
Funded by:
Europäische Union
Funding reference: 820789
Duration: 01.10.2018 - 30.09.2021OptiPerm
OptiPerm
Research on the production of functional films with optimized permeation barrier coatings
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 3000651169
Duration: 15.09.2015 - 14.09.2018Papierstab
Papierstab
Stabilization and preservation of brittle wood-containing papers through the use of novel biopolymer-based materials. Sub-project: Process developments for the production of nanocellulose using electron beams and for elastic crosslinking of long-chain monomers by means of UV radiation
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 3000642216
Duration: 14.03.2016 - 31.03.2018PhotonFlex
PhotonFlex
Photonic process chain for the production of flexible organic solar cells in roll to roll Process / Barrier test Film welding
Funded by:
Land Nordrhein-Westfalen
Funding reference: EU-1-1-078E
Duration: 01.01.2017 - 31.12.2019
PI-SCALE
PI-SCALE
Shaping the future in OLED lighting
Funded by:
Europäische Union; Horizon 2020 Programm
Funding reference: 688093
Duration: 01.01.2016 - 31.12.2018PolAR
PolAR
Polymeric films with anti-reflection properties by plasma etching
Funded by:
Bundesministerium für Wirtschaft und Technologie
Funding reference: 16/N0723
Duration: 01.10.2008 - 30.09.2011PolyCollect
PolyCollect
Investigations on technologies for high-rate evaporation of thin plastic foils for battery current arresters
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100385882
Duration: 01.10.2019 – 30.09.2021
PoSiBat
PoSiBat
Highly-porous silicon-zinc coatings for batteries with very high energy density
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 3000659083
Duration: 01.09.2016 - 31.08.2018ProSiSt
ProSiSt
Process technologies for structured silicon layers as anodes in high-energy lithium batteries Sub-projects: Fundamentals of thin film and etching technology and cell concepts
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 03XP0130D
Duration: 01.10.2017 - 30.09.2020ProSoLitBat
ProSoLitBat
Joint project: ProSaLitBat, Sub-project: Innovative roll-to-roll process for high-rate vacuum coating of metal foils with solid electrolyte layers
Funded by:
Verein Deutscher Ingenieure
Funding reference: 13N13236
Duration: 01.090.2017 - 31.08.2017PVD-Direkt
PVD-Direkt
High-energy and high-rate PVD process for efficient direct-metallization of plastic components
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100276002
Duration: 17.10.2016 - 16.10.2019R2RBattery
R2RBattery
Tailor-made material systems and technologies for roll-to-roll production of electrochemical energy storage devices on flexible carriers - Highly valence ions for energy revolution
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 03SF0542B
Duration: 01.09.2013 - 31.08.2019R2D2
R2D2
Roll to Device 2 (R2D2) - Teilvorhaben: Fertigungstechnologien für flexible OLED
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 13N12948
Duration: 01.09.2013 - 31.08.2015RadarGlass
RadarGlass
Design and manufacture of functional glass surfaces for the manipulation of radar waves - RadarGlass Sub-project: Deposition of transparent conductive coatings for frequency selective surfaces
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 03VP03202
Duration: 01.07.2017 - 30.06.2020Siphon
Siphon
Programme "Central Innovation Programme for Medium-Sized Enterprises (ZIM)" with project: Development of a TiO2-coated siphon from a sintered body made of metal fibres as a microbiological barrier in the outlet of the wash basin; development of a process for titanium dioxide coating of the sintered body made of metal fibres and a process for activating the titanium dioxide layer with UV light.
Funded by:
Bundesministerium für Wirtschaft und Energie
Funding reference: ZF4597702BA8
Duration: 01.01.2019 - 30.12.2020SmartBarrier
SmartBarrier
Joint project: Innovative processes for the manufacture of flexible products
Funded by:
Bundesministerium für Bildung und Forschung
Funding reference: 01RI0628A
Duration: 01.01.2007 - 30.06.2010SMILE
SMILE
Customized multifunctional high-performance surfaces for energy-efficient and sustainable components and tools; Smart and Resilient
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 800034
Duration: 01.08.2020 - 31.12.2020
TALENTA
TALENTA
TALENTA excellence
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: BEBF98 BAT
Duration: 01.01.2020 - 31.12.2021TASG
TASG
Portable, self-sufficient and compact power generators (TASG), Sub-theme: Development of coating technologies and ASIC for TASG
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100347675
Duration: 01.02.2019 - 31.12.2021TFE4OPV
TFE4OPV
Joint projects: Research on technologies for the efficient thin-film encapsulation of flexible electronic components Sub-theme: Research on a PECVD process for the pre-encapsulation of laser-structured flexible electronic components
Funded by:
Europäische Union
Funding reference: 100374326
Duration: 15.07.2019 - 31.12.2021Theranostische Implantate (Fraunhofer Leitprojekt)
Fraunhofer Lighthouse Project: »Theranostic Implants«
Approval-relevant development of key technologies
TopBePro
TopBePro
Investigation of location-dependent coating profiles. Sub-project: Coating technology for the deposition of location-dependent coating profiles and for low-particle precision coating on 2D and 3D components.
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100206481
Duration: 01.03.2015 - 28.02.2018Torero
Torero
Development of a ring CT system for fast inline testing of "endless" products and bulk material systems
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 838 845
Duration: 2019 -2020TREASORES
TREASORES
Transparent Electrodes for Large Area, Large Scale Production of Organic Optoelectronic Devices
Funded by:
Europäische Union (7th Framework Programme FP7)
Funding reference: 730871
Duration: 01.11.2012 - 31.10.2015Young Research Class
Young Research Class
Resilience of critical infrastructures
Funded by:
Fraunhofer-Gesellschaft zur Förderung der angewandten Forschung e. V.
Funding reference: 809 011
Duration: 01.03.2020 - 28.02.2021ZeoMet
ZeoMet
Improvement of the energy flow in zeolite heat accumulators by vacuum metallization of the granules (ZeoMet)
Funded by:
Sächsisches Staatsministerium für Wirtschaft, Arbeit und Verkehr
Funding reference: 100346109
Duration: 01.11.2019 – 31.10.2021
